RE14010C2D REV A Amana Air Conditioner Parts List

Adjustable peg clip (clip, adjustable peg)

This dishrack clip is intended for use with dishwasher dishracks that have adjustable pegs. This clip is only about four inches long.

Washer water inlet valve with thermistor (washer water inlet valve assembly)

This part is used to help control and balance the water temperature flowing in to the washer tub.

Upper dishrack with wheels (sub 99001454)

This rack comes complete with four attached wheels and the rack may differ in appearance, but will function same as original part.

Garbage disposal drain stopper (stopper asm)

This is a flexible black rubber cover that is over the top of the sink drain. It helps keep liquids and smaller food particles from splashing back into the sink. With normal wear and tear of the splash guard it will eventually need to be replaced. The splash guard is approximately 3 inches in diameter. This is a genuine OEM part.

Drive v-belt (use 134161100)

This drive belt is designed to ride on the pulley until the basket gets up to speed. If your washer drum will not agitate or spin, you may need to replace your belt. It is recommended to disconnect the power to your washer and shut off the water supply before you start your repair. This drive belt is a genuine OEM part.

Refrigerator ice bucket and auger assembly (bucket & auger asm)

Tub spring (spring, counterweight)

This suspension spring is used to support and balance the outer tub of your washer. If the spring is broken it will cause the washer to be noisy and off balance during the spin cycle. Please check your model to see how many springs are required for your model. The spring is sold individually. This is a genuine OEM part. Please make sure you disconnect the power to the washer before starting your repair.

Oven rack (rack oven)

This single chrome oven rack provides a reliable flat cooking surface for your cookware inside of the oven cavity. The oven rack is made of metal and measures approximately 24” wide by 17 1/2” deep. This is a genuine OEM part and is sold individually. Please order quantity needed.

Drawer slide rail - right side (slide asm rh)

This is the drawer slide rail or slide assembly for your refrigerator. You will find the drawer slide rail at the bottom of your refrigerator, mounted to the right-hand side of the cabinet wall. It is designed to hold the bottom shelf in place. You will want to make sure you are replacing the bottom rail, as the top one is a longer rail. The slide rail is held in place with two Phillips screws and is made of white plastic.

High limit thermal fuse

Meant as a backup to a high limit thermostat, this fuse is typically set to trip at a higher temperature than that of a high limit thermostat. This is a one-time use fuse, so when it does trip, you do need to replace it. It's letting you know that something is wrong with your dryer.

Door shelf retainer bar (door shelf trim)

This refrigerator door shelf trim is approximately 28 inches long. It is all white in color, and it is made entirely of metal. NOTE: The image may not be of the exact product but will function properly.

Door basket assembly (door basket)

Refrigerator door bin AAP73252202 is an original equipment manufacturer (OEM) part that fits some Kenmore Elite bottom-freezer refrigerators in the following series: 7957204, 7957205, 7957209, 7957218, 7957248, 7957311, 7957315, 7957401, 7957402, 7957404, 7957409, 7957504, 7957998 and 7957999. Also fits some LG bottom-freezer refrigerators in series LFX25991, LFX31925, LFX31935, LFX33975 and LMX31985. This door bin has an irregular shape?it's 13-1/2 inches wide, 9-1/2 inches deep on the left, 10-1/8 inches deep on the right and 4-1/4 inches tall. To install door bin AAP73252202, slide it into the door just above desired location and push down on the bin until it snaps into place.

Igniter-oven (range oven igniter)

This flat style gas oven igniter has ceramic housing and comes with a connector.

Door shelf end cap - left side (use 5303324302)

This is the door shelf end cap for your refrigerator. It connects to the refrigerator door and keeps the door bar in place. Your refrigerator will have two shelf end caps, one for the right side and one for the left. This part is the left side door shelf end cap. It is made of white plastic and is a little over two inches long. This is an OEM part from the manufacturer and is sold individually.

Bumper (bumper, grate bottom)

This burner grate pad, also known as a grate foot, is located on the bottom of your gas cooktop grates to prevent them from moving and scratching the top of your appliance. The grate foot must be held in with adhesive that is not included with the part. It must be ordered separately. The part measures 0.2” and is black in color. This is a genuine OEM part and is sold individually.